Відео

Does the ground wire have to be white instead of green like usual?

trust me you buy new side skirt for nothing lmao

Nice to see the Renegade do other things than mud bogging. I myself prefer trails and water crossings than soupy mud runs.

Thanks for the input. I caught the conversation in comments about the slider in the carb wearing. Is that pretty common and what solutions are there other than buying new? Dealer is $187 if they can get it. Unfortunately it also sounds like this machine has already had the OEM carb replaced with aftermarket. Any advice for finding a reasonably priced OEM (eBay not looking good)?

Couldn’t get the video uploaded. Practically no rev capability.

Great overview b/c I’m looking at one right now to possibly buy. It does need new pull cord & cover panel for that side, but the carb sounds like a big issue on this one. Starts & idles (electric) just fine, no smoke. But doesn’t throttle or ramp rpm well. I’d like to share the video of this that I got today and see what you have to say. Called local Kawasaki to see what OEM carb might cost & check availability. It’s not (2003-4 I think) anymore. Carb slide is but almost $200 now. Looks like lots of universal near fit Chinese carbs are available online, I think that’s what’s on it now too. Advice?

Could this be the problem for me to even if i have the electric shifter?

Has the creek ever gotten high enough to wash over the bridge? How has it held up?

Does anyone know the top speeds on these because I like how they look and I like the price range but I also want something that is fun to rip around the road and trails

I hve one and the ramp needs to be longer. My jeep is lifted and the short ramp on a lifted vehicle make it hard to push up the ramp.

Corsa sounds so much better

Have any videos on getting the fuel system to function correctly?

This whole hydraulic system seems like it should be used as a demo for what not to do when designing a hydraulic system.

Thank you. My 2000 Foreman 450s had this problem after sitting 9 years. Hooked it up with a chain to my trailer hitch. Secondary broke free. Shifts great now. ❤

how to get the shaft apart?

I have a 1990 350d. When I put it up for winter I ALWAYS install a ratchet strap between the shifter and handle bar to keep the shifter up and the clutch released while in storage. Never had any issues!

I was needing a Jetski Trailer,that can be Broken Down for Storage,, so i went to Amazon,& this popped up..is there another brand,that i could also consider

Thanks for saving my back ! I am having clutch slip problems and I will be trying this !! You rock !!

Thanks. Purchased a waterproof lighted switch just now after watching for my 06 rancher 350. Just finishing a top end freshening up and I want the engine running cooler than Honda sets that switch temp at to activate.

Thanks, changed the engine oil today , and need to tackle this also. What weight oil did you use? thanks

if you still have the truck, this might be a recall on the Superduty trucks. Since you replaced yourself, they might be able to reimburse the cost.

I bought one for 600 from my uncle it needs lil repairs but the frame and engine are in good condition probably going to have to put another 1200 into it, think it’s worth it for this bike?

anyone knows a good source of parts for these in Canada let me know!

I have a 2014 Durango rt and I did the say swap and I’m having issues with the bumper fitting and for the headlights did u rewire them ?

Perdy

I'm here 4 years later and paid $165 using a coupon 😂

Does this have the single line slave cylinder, or the slave with the bleeder screw? I have an 02 explorer with a manual, and the slave just has 1 line in. There's a bleeder on the firewall, but I don't see how that clears air out of the slave, which is downstream from the bleeder. Every video I see is for bleeding the slave with the bleeder screw. I'll try this and see if it helps, but I still have to bleed my slave somehow

C6 z51 2008-2009 es mas rapido que grand sport ☝️🤠

Hola soy de Valledupar Colombia me puedes ayudar a comprar un ironton

Was it just the needle bearing that was bad?

What size spark plug wrench is it ?

I got all that parts you suggested spent 4 hours trying different things to get the bearing of but what worked for me I drilled several holes around & through the bearing and was able to twist it off after using a sawzall blade to cut a little bit that was holding everything together I just wrapped the blade in a towel until I was able to cut it in half. Thank you soo much.

will a 5 yr old in a booster seat fit nicely in the back of the 230i. I want to get one maybe. it’s safer then my mini countryman and slighter longer.

I change engine oil every 100 hours. I change hydro filters at the same time. Then I add about 1 gallon of hydraulic oil and done.

I have the ZG327. Your video is so helpful. Thanks a lot.

What size pipe after the resonator?

Best video on this yet!!! VERY VERY HELPFUL

Got a 2013 raptor they are insane

I've completed all these works on my 350D - same parts, same process and also consulted the workshop manual during the adjustment & bleeding process. However the biting point of the brakes is so close to the handlebar and seems spongey. Takes multiple pumps to get a good feel on the lever. Did you have this issue? I got no leaks and inspected for flowback to the reservoir during brake hold process. Any thoughts?

What size bolt is that on the stabilizer brackets?? Mine came with the wrong one !

Not helping

The one I have goes 30, I had one hand on the steering and the other on my phone to look how fast I was going. I thought it would go faster

Corsa all day bro

nice detail, Thanks

This is nice tie bridge but don’t think we need anything that nice

Thank you.

Thank you

I have the same HF bleeder, but I find I don't have a steady stream of fluid coming out. It's more like the top of of the top is air, and the bottom half is brake fluid rushing out. Am I doing something wrong?

What the top speed on it

Hello, I have this same bolt capture installed. Is there a way to do your belt service/replacement with it installed since you can no longer get a socket on the crank bolt the rotate and relieve/re-tension the belt